#VISAGE GPS CONSOLE COMMANDS INSTALL#
#VISAGE GPS CONSOLE COMMANDS ARCHIVE#
#VISAGE GPS CONSOLE COMMANDS SERIES#

For example, the remotestate monitor is scheduled using the command: (port1/2)]# config monitor remotestate When the modem is initialized using the config init command, the chassis and console log monitor will automatically be scheduled.Īdditional monitors to capture information on RF statistics from the modem can be scheduled using the config monitor command at the port level.

Terminal - Captures user interactions with the device.

The results may be displayed with the show device syslog command.

ConsoleLog - Captures system error logs as they are displayed via the console.

The results can be displayed with the show pingstats command.

Ping - Executes an ICMP ping to a specified IPv4 address from the modem's context.

Remotestate - Checks the status of the iDirect with regard to receive and transmit power, frequency and errors, FSD, IGroup, HDLC, CompID, receive lock, link layer, modem state, receive AGC, receive signal-to-noise ratio and receive tmdlost.

Interface - Captures information on the Ethernet and tunnel interfaces and includes RX/TX bytes, interface resets, link state, etc.

Chassis - Checks the status of the iDirect with regards to CPU usage, Falcon's status, configuration errors, temperature and memory.

There are six monitors for the iDirect modem: chassis, interface, remotestate, ping, consoleLog and terminal.

The results can be used to trigger an alarm, event or to take other automated actions. Monitors collect chassis and interface data from supported devices. Upon login you should see the iDirect prompt.

#VISAGE GPS CONSOLE COMMANDS ARCHIVE#

Running-config saved to archive as current. This session takes place within your Uplogix appliance session. Issue the terminal command to start a terminal session with the modem. Use null modem (rolled cable to device)? (y/n): nĭo you want to commit these changes? (y/n): y (port1/2)]# config initĬonfigure dedicated ethernet port? (y/n) : Use the config init command to configure the port for iDirect. In the example below the iDirect modem is attached to port 2. Issue the port command to switch to navigate to the port your iDirect modem is connected to. Use a workstation to open a command line session with the Uplogix appliance. This cable is available as Uplogix part number UP610031 CABLE,UPLOGIX-iDIRECT-SEATEL NO CONNECTOR, or UP610033 CABLE,UPLOGIX-iDIRECT-SEATEL DB25.įor example, the Sea Tel terminal mounting strip wiring diagram is displayed below. Below is an example wiring diagram describing the split cable configuration. There are two pins carrying key information between the antenna and the modem: RJ-45 pin 2 which carries the AGC threshold information and RJ-45 pin 7 which carries TX Mute. With the Uplogix appliance managing the modem via a console connection, it is necessary to create a split cable for this information to pass directly between the antenna and modem uninterrupted. In the maritime or mobile environments, key information is passed between the antenna and the modem. In a terrestrial or fixed installation, connect a standard Cat5/patch cable between an available Uplogix port and the console port of the iDirect modem. Physical Installation Terrestrial Environment

Executing single line commands and parsing the results.

Set latitude/longitude position - Because the Uplogix uses transmit and receive pins of the iDirect console port to interact, the NMEA-183 output of a GPS antenna cannot be plugged directly into the console port and must be monitored on another Uplogix port.

#VISAGE GPS CONSOLE COMMANDS SERIES#

Automating Actions - Executing common maintenance tasks on demand or as a series of automated actions.Capturing Raw Buffer Logs - Current and previous raw interaction logs are available for review.Console Message Logging - monitor console log messages.Interface Monitoring - ability to monitor Ethernet and tunnel interfaces.RF Parameter Monitoring - monitor operational Radio Frequency (RF) elements.Key Parameter Monitoring - Maintaining a database of historical operational statistics.

#VISAGE GPS CONSOLE COMMANDS INSTALL#

Operating System Management - Store and install specific package or operating system images.

Capture extended configuration elements outside the option file.

Configuration change detection and automated rollback.

Option File Management - Ability to store and manage multiple versions of option files on the Uplogix appliance.

LMS 6.0 includes support for iDirect satellite modems including 8000, 7000, 5000, 3000, X3, X5 series standalone, and iConnex models. The purpose of this document is to detail the installation and configuration of iDirect satellite modems for use with Uplogix appliances.

Visage gps console commands